Digital Monitoring Products XR550 Manuale delle Istruzioni Scaricare il pdf (Pagina 12)

Digital Monitoring Products XR150/XR350/XR550 Series Programming Guide

INTRODUCTION

1.3 Encrypted Communications (XR550 with Encryption only)

Some installations require secure data communications. Use a unique passphrase to enable encrypted

communications and provide a secure means for data communications. See Network Options.

An XR550 panel with encryption communicates using 128-bit or 256-bit AES encryption. If you currently have

an XR550 panel with network installed, you may purchase a separate feature key to activate encrypted

communications using the Feature Upgrade process. Encrypted communication cannot be enabled on a standard

XR550 panel. For more information on the Feature Upgrade process see Section 21 in this document.

1.4 Programmer Operation

There are 20 programming sections to choose from:

Programming Item Section in This Manual Programming Item Section in This Manual

Initialization 2 Output Information 12

Communication 3 Output Groups 13

Network Options 4 Menu Display 14

Messaging Setup 5 Status List 15

Device Setup 6 PC Log Reports 16

Remote Options 7 Area Information 17

System Reports 8 Zone Information 18

System Options 9 Stop 19

Bell Options 10 Set Lockout Code 20

Output Options 11

To choose a section for programming, press any top row Select key when the keypad displays the name of that

section. Sections 2 through 20. contain detailed instructions for each programming step.

1.5 Programmer Lockout Codes

The panel allows you to enter the programming function without entering a lockout code using steps 1 to 4 listed

in Getting Started. We recommend, however, that you install a Lockout Code to restrict programming to only those

persons your company authorizes. You can do this by using the SET LOCKOUT CODE feature in the Programmer. The

Lockout Code restricts any unauthorized panel programming.

After resetting the panel and entering the code 6653, the keypad displays PROGRAMMER. Press COMMAND to

advance through the programming sections until SET LOCKOUT CODE displays (after STOP). Press any top row Select

key. The keypad displays ENTER CODE: – . Enter a 3 to 5 digit Programmer Lockout Code and press COMMAND. The

keypad displays ENTER AGAIN followed by ENTER CODE: –. Enter the same 3 to 5 digit code a second time and press

COMMAND. The keypad displays CODE CHANGED.

Note: The panel does not accept a 5-digit Lockout Code higher than 65535.

Before accessing programmer functions enter the new code number. Write the Lockout Code number down and

keep it in a secure place with access limited to authorized persons only. Lost Lockout Codes require the panel to be

sent back to DMP for repair. You may cancel a Lockout Code by entering 00000 at the Set Lockout Code command.

1.6 Reset Timeout

The panel has a feature that requires you to enter the Programmer within 30 minutes of resetting the panel. After

30 minutes, if you attempt to program by entering the 6653 (PROG) code, the keypad displays: RESET PANEL. You

must reset the panel and enter the program code then begin programming within the next 30 minutes.

If you are already in the Programmer and do not press any keys on the programming keypad for 30 minutes, the

panel terminates programming. All data entered up to that time is not saved unless you run the Stop routine.

Note: Use the Stop routine to exit panel Programming. Ensure the keypad displays “SAVING PROGRAM” to save all

programming changes entered.

1.7 Power Up

When the panel is powered up after an AC power failure, any zone transitions are not recognized for 60 seconds.

Normal zone processing resumes at the end of the 60 seconds.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 77 78

Commenti su questo manuale

Nessun commento

Digital Monitoring Products XR550 Manuale delle Istruzioni Pagina 12

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Digital Monitoring Products XR550