Digital Monitoring Products XR20 Guida di Installazione Scaricare il pdf (Pagina 13)

XRSuper6/XR20/XR40 Programming Guide

2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products

3.7 EVENT MANAGER

This option specifies when non-alarm reports are sent to the receiver. This selection

does not affect zone alarm, zone trouble, zone restoral, supervisory, or serviceman

messages. Closing reports are not delayed if you have programmed a YES for the

Bell Test option.

SND - All reports are sent to the receiver as they occur.

DLY - All non-alarm reports are held until the panel's memory buffer contains 40

events on the XRSuper6, 66 events on the XR20, and 100 events on the XR40, or until

the panel's next communication with the receiver.

Note: If BELL TEST is YES, Closing reports are not delayed.

KEEP - All non-alarm reports are held in the panel's memory buffer until they are

overwritten by new activity. You can view the contents of the buffer using the DMP

Remote Link™ software, or the Display Events function in the User Menu. Contact ID,

Modem IIe, and 4-2 formats do not delay reports but send them as they occur.

Time update from the SCS-1 Receiver: The XRSuper6/XR20/XR40 requests a time

update each time (once each day maximum) the panel contacts the receiver. The

SCS-1 Receiver must have firmware version SCS/805 or higher and the Update Time

to Panel option must be set to YES in the receiver's Host Configuration screen. In

addition, the central station automation system must be configured to update the

time in the receiver at least once each day.

3.8 TEST FREQUENCY

Allows you to set how often the panel's test report is sent to the receiver. Enter

from 1 to 60 days. Enter zero to disable the test report.

3.9 TEST TIME

Press COMMAND to enter the Test Time. Enter the time of day the panel sends the

test report to the SCS-1 Receiver. Use entries between 12:00 to 11:59 and then

choose AM or PM.

3.10 RECEIVER 1 PROGRAMMING

Allows you to set the options for the first receiver the XRSuper6/XR20/XR40 panel

attempts to contact when sending reports. The XRSuper6/XR20/XR40 supports

communication to two receivers.

3.11 ALARM REPORTS

YES enables Abort, Alarm, Alarm Restoral, Alarm Bell Silenced, Ambush, Exit Error,

and System Recently Armed reports to be sent to this receiver.

3.12 SUPERVISORY/TROUBLE REPORTS

YES enables Supervisory, Trouble, Trouble Restoral, Force Armed, and Fault reports

to be sent to this receiver.

3.13 OPENING/CLOSING AND USER REPORTS

YES enables Opening/Closing, Door Access, Schedule and Code Changes, Bypass, and

Sensor Reset reports by user to be sent to this receiver.

3.14 TEST REPORT

Enter YES to enable the Recall Test report to be sent to this receiver.

3.15 BACKUP REPORTING

YES enables this receiver to be a backup to the other receiver in the event the other

receiver cannot be contacted.

Note: When Backup Reporting is set to YES, the Cellular Backup Output programmed

in Output Options is automatically set to zero.

BACKUP NO

O/C USER YES

SPV/TRBL YES

ALARM YES

TEST TIME

0 : 0 0 A M P M

RECEIVER 1 PROG

TEST RPT YES

TEST FREQ: 0

EVENT MGR: SEND

SND DLY KEEP

COMMUNICATION

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 37 38

Commenti su questo manuale

Nessun commento

Digital Monitoring Products XR20 Guida di Installazione Pagina 13

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Digital Monitoring Products XR20